Xp setup wireless home network

Yes No. Not Helpful 6 Helpful 6. You will need a central access point to connect to and control communication among the wireless devices. Not Helpful 6 Helpful 5.

VMWare does not virtualize a wireless card. These directions would only be applicable if you used PCI Passthrough with a wireless card in your host computer.

Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Submit a Tip All tip submissions are carefully reviewed before being published. You Might Also Like How to. How to. About This Article. Tested by:.

Co-authors: Updated: May 6, Thanks to all authors for creating a page that has been read , times. Is this article up to date? A broadband Internet connection is a high-speed Internet connection. You can get a broadband connection by contacting an Internet service provider ISP. ISPs frequently offer broadband modems. You can also find these at computer or electronics stores, and online.

Wireless router. A router sends info between your network and the Internet. With a wireless router, you can connect PCs to your network using radio signals instead of wires. Wireless network adapter. A wireless network adapter is a device that connects your PC to a wireless network.

To connect your portable or desktop PC to your wireless network, the PC must have a wireless network adapter. Most laptops and tablets—and some desktop PCs—come with a wireless network adapter already installed. Select Start , type device manager in the search box, and then select Device Manager. After you have all the equipment, you'll need to set up your modem and Internet connection.

If your modem wasn't set up for you by your Internet service provider ISP , follow the instructions that came with your modem to connect it to your PC and the Internet. If you're using cable, connect your modem to a cable jack. Put your wireless router somewhere where it will receive the strongest signal with the least amount of interference. For better results, follow these tips:.

Place your wireless router in a central location. Place the router as close to the center of your home as possible to increase the strength of the wireless signal throughout your home.

Position the wireless router off the floor and away from walls and metal objects , such as metal file cabinets. The fewer physical obstructions between your PC and the router's signal, the more likely that you'll be using the router's full signal strength.

Reduce interference. Some networking equipment uses a 2. This is the same frequency as most microwaves and many cordless phones. If you turn on the microwave or get a call on a cordless phone, your wireless signal might be temporarily interrupted.

You can avoid most of these issues by using a cordless phone with a higher frequency, such as 5. The big benefit for home environments is that a wireless LAN does away with the need for cabling. You may need to add an expensive Access Point to extend the range of the LAN and, even so, it may not be sufficient. The bottom line is, if you decide to go the wireless route, make sure the store will refund your money if the LAN will not provide reliable performance within the specified range.

Make a list of the hardware you need for each computer, not forgetting any cabling, and buy it. These kits contain all you need to set up a two- or three-PC network. Install the network adaptors and install your modem on the ICS host computer you can also let the computers connect to the Internet independently by installing modems on each. Physically cable the computers and hubs or routers together.

Follow the instructions in each screen and press Next to continue. XP's Network Setup Wizard takes much of the pain out of setting up a home network. Make sure you maintain an active Internet connection on your host computer as you proceed through this process. If you want a really easy networking experience and you have the hardware to support it, consider clean installing Windows XP on two or more computers. First install your network hardware network interface cards, cabling, et cetera , then perform a new installation of Windows XP.

During installation, XP will sense your hardware setup, ask for a name for each computer, and then ask which type of setup you wish to create. The Task Pane in My Network Places lets you view your network connections and view each of the computers in your workgroup the workgroup consists of all computers on a network which share the same workgroup name — by default, XP gives all computers on your home network the workgroup name MSHOME, although you can change this if you wish.

Provided, that is, your sister decides to share her printer.